Famco Chimney Sweep Nationwide

Famco Chimney Sweep in Fort Lauderdale: What to Know First

We’re an independent Famco service provider in Fort Lauderdale, and we sweep, inspect, and repair Famco chimneys without the manufacturer markup or the runaround. Most Famco chimney sweeps in the area are done in a single visit, usually within 60 to 90 minutes, and a standard sweep typically runs $189 to $289 depending on creosote buildup and access. This page is for homeowners with a Famco fireplace or chimney system who want to know what’s actually inside their flue, what it costs to clean it, and who in Fort Lauderdale will do the work without leaving a mess or a mystery charge.

Call (754) 354-1430

Need a sweep or an inspection? Call (754) 354-1430 and a live person answers, day or night.

How Famco Products Fail – and How We Fix Them

We’ve cleaned and repaired enough Famco systems across Fort Lauderdale to know exactly where they wear, what clogs them, and what actually needs fixing versus what can wait. Here’s what we see on the job, by the part.

• Famco stainless steel chimney caps with plugged mesh. The mesh screen on many Famco caps is fine enough to trap salt-laden air and creosote together. In Fort Lauderdale, that combination hardens into a crust that blocks airflow and causes smoke to roll back into the living room. We remove the cap, soak and wire-brush the mesh, and if the screen is corroded through, we replace it with an OEM Famco cap or a quality Copperfield equivalent, whichever we can get faster and with the better written price for you.
• Creosote glazing in Famco wood-burning fireplace flues. Famco wood-burning units are common in older Fort Lauderdale ranch homes near Plantation and Wilton Manors, and the flues often run cooler than modern inserts. That means stage 2 glazed creosote, the shiny tar-like stuff that a basic brush won’t budge. We use a rotary whip with polymerized rods to break the glaze off without scarring the liner, then a HEPA vacuum to catch what falls.
• Galvanic corrosion at the Famco anchor plate. Salt air from the Atlantic works on the point where the Famco anchor plate meets the chimney crown. We regularly see white chalky corrosion there, which eventually loosens the plate and lets water in. During a sweep, we inspect the anchor plate bolts and crown sealant. If it’s degraded, we reseal with a high-temp silicone rated for South Florida humidity and tell you plainly whether the plate itself needs replacement now or can safely last another season.
• Draft problems tied to Famco chimney height. Some older Famco installations in Fort Lauderdale were done with flue terminations too close to the roofline or nearby trees. When a chimney can’t draw because the cap sits in a dead air pocket, the fireplace smokes on mild days, not just during windstorms. We diagnose this during the sweep by checking termination height against the 10-foot/2-foot rule and the roof slope, then tell you the specific correction, which is often a simple cap or extension, not a rebuild.
• Animal debris in unused Famco fireplaces. Fort Lauderdale has no shortage of birds, iguanas, and raccoons, and a Famco fireplace that hasn’t been used in a few seasons becomes a nest site. We’ve pulled everything from dried palm fronds to a full anole colony out of Famco flues. A Level 1 or Level 2 inspection during the sweep confirms whether you need a better cap or mesh upgrade, and we’ll show you the photo before we recommend any of it.

Our Famco Chimney Sweep Process

Here’s how a Famco chimney sweep works when you call Flint Chimney Co Fort Lauderdale.

1. 1
   Phone call. You speak to a live person, not a voicemail. We ask about your Famco unit, the last time it was cleaned, and any smoking or odor issues. Then we schedule a time that works, and you get the written price range before we arrive.
2. 2
   Site prep and initial inspection. We lay drop cloths around the hearth and run a floor-level inspection of the firebox, damper, and smoke chamber before any sweeping starts. If we see cracks, missing mortar, or a deteriorated liner section, we note it for the camera inspection.
3. 3
   Creosote and soot removal. Using brushes sized to the Famco flue dimensions, we sweep from the top or bottom depending on access and vent configuration. For glazed creosote, we switch to the rotary whip. Every pass is followed by the HEPA vacuum, so nothing settles on your mantel or furniture.
4. 4
   Camera inspection and photo report. We run a push-camera up the entire flue length after the sweep. You see every photo. If the liner is cracked or spalled, we tell you and show you. No recommendations without evidence, and that’s a hard rule with us.
5. 5
   Parts decision. If a Famco cap, anchor plate, or damper component needs replacement, we give you a written quote for OEM Famco and quality aftermarket options like Copperfield or DuraFlex, with the price difference stated plainly. You approve the part before we order anything.
6. 6
   Final test and guarantee. We fire-test to confirm the draft is correct, then walk you through what we found and what we did. Repairs carry our 365-Day Done Right Promise in writing. If a covered repair fails within a year, we return at no charge.

What Famco Chimney Sweep Costs in Fort Lauderdale

An honest price up front is the only way we work, so here’s what Famco owners in Fort Lauderdale can expect to pay.

• Standard Famco chimney sweep: $189 to $289, depending on creosote level and access difficulty.
• Chimney sweep with Level 1 inspection: $249 to $349. This is the right scope for most annual cleanings.
• Chimney sweep with Level 2 camera inspection: $399 to $549. We recommend this if you just bought the home, had a chimney fire, or the unit hasn’t been swept in 3+ years.
• Glazed creosote removal: Add $75 to $150 for rotary treatment when stage 2 creosote is present.
• Famco cap, damper, or anchor plate replacement: Quoted separately after inspection, typically $175 to $650 depending on the part and finish.

What moves the price: creosote stage, roof pitch and height, whether the flue has a liner that needs special brushes, and whether we find animal debris or obstructions that require extra removal time. Call (754) 354-1430 for a free written estimate based on your Famco system. You’ll get the number before the truck rolls.

Why Fort Lauderdale Homeowners Call Flint Chimney Co Fort Lauderdale for Famco Work

Hank Delano built Flint Chimney Co on a simple idea: tell the homeowner what you found, tell them what it costs, then do the work clean. That’s how we run every Famco sweep in Fort Lauderdale. We’re part of the Garrison Partners family, founded in 2002, and we operate under the Garrison Standard: a written price before any work starts, background-checked and uniformed technicians on every call, and a 365-Day Done Right Promise on all repairs. If a repair we make fails within one year, we come back and make it right at no charge, no argument. And since we work with more than just Famco, if your chimney needs a DuraFlex liner, a HeatShield resurfacing job, or Gelco sealant, we can spec the right material for the job without brand bias. Famco is the brand on your fireplace. We’re the crew that keeps it working.

FAQs