Gelco Chimney Inspection Nationwide

Gelco Chimney Inspection in Fort Lauderdale: What to Know First

Gelco chimney inspection in Fort Lauderdale typically costs $189 to $425 depending on which inspection level your fireplace and venting setup requires, and most inspections are completed in one visit. We’re an independent Gelco service provider, not a manufacturer-authorized shop, which means we inspect the full system and tell you exactly what we found without any warranty department looking over our shoulder. If you own a home with a Gelco chimney cap, Gelco chase cover, or Gelco flashing component anywhere in Fort Lauderdale or Broward County, this page tells you what to expect. Call (754) 354-1430 for a written estimate before any work begins.

Call (754) 354-1430

How Gelco Products Fail – and How We Fix Them

• Gelco chimney caps with rust-through at the screen welds. Gelco caps use a fairly standard galvanized steel screen, and in Fort Lauderdale’s salt-spray air, the fine wire mesh is almost always the first thing to go. We see this constantly on homes from Victoria Park to Coral Ridge. The cheap fix is a cap replacement with a higher-grade stainless mesh that is available through non-OEM suppliers without costing more than the cap itself.
• Gelco multi-flue caps with failed mounting brackets on older tile crowns. The bracket system works fine on a clean, flat crown. It does not work fine when the crown has hairline cracks from twenty years of Florida sun and rain. The brackets loosen, the cap shifts, and now you’ve got a capped flue that’s off-center and leaking around the edges. We fix this by resetting the cap on a repaired and sealed crown, using additional mechanical anchors where the crown condition allows.
• Gelco chase covers with perimeter gasket breakdown. Gelco chase covers rely heavily on a gasket seal along the bottom lip. In Fort Lauderdale humidity, that gasket cooks and splits, which means water gets under the cover and follows the chase down the house. The factory gasket is not sold separately as a small-item replacement, so our repair approach is to remove the cover, clean the contact surface, replace the seal with a commercial-grade neoprene equivalent, and reassemble with proper rust-proof fasteners.
• Gelco flashing kits used on mis-sized openings. A lot of Fort Lauderdale contractors installed Gelco flashing over hand-cut chase openings that don’t quite match the product’s spec. The result is visible daylight gaps at the corners that the installer filled with caulk, which fails within a season or two. During inspection we flag this immediately: the cap and flashing are not damaged, the installation was wrong from the start. The right repair is a custom-fit chase top, not another tube of caulk.
• Gelco cap tops with dented or bent dampers from hurricane-season debris. It’s South Florida. Palm fronds, fence boards, parts of umbrellas from three houses down. We’ve found Gelco caps on Fort Lauderdale roofs with impact damage that jammed the damper linkage shut or partially open. If the damper is not moving freely, the fireplace can pull smoke back into the room. Our inspection documents this, and the repair usually means replacing the damaged damper assembly rather than trying to straighten a bent plate.

Our Gelco Chimney Inspection Process

Every Gelco inspection in Fort Lauderdale follows the same sequence, so you know exactly where we are in the job and what happens next.

1. 1
   Call and scheduling. A live person answers, takes your address and the nature of the Gelco concern, and books a window that actually matches the calendar.
2. 2
   Arrival and system review. The technician walks the property with you, looks at the fireplace, roof access, and any visible Gelco components, and explains the inspection level that fits your situation before touching anything.
3. 3
   Component-by-component inspection. We examine the chimney structure, flue liner, damper operation, Gelco cap and flashing seals, and the roof-to-chase connection. A camera is run when the job calls for it.
4. 4
   Findings summary with camera evidence. You see the photos and video, not just a verbal summary. No recommended repair is made without visual proof you can review yourself.
5. 5
   Written recommendations. We hand you a scope document that itemizes what we found, what it means, what is urgent and what can wait, and the exact price for each line item if repair is needed.
6. 6
   No-fuss close-out. If you approve work, the price on the written estimate is the price on the invoice. Every repair carries the 365-Day Done Right Promise in writing.

What Gelco Chimney Inspection Costs in Fort Lauderdale

Simple answer: a Level 1 inspection for a single fireplace with a Gelco cap and basic chase runs $189 to $249. A Level 2 inspection, which adds the camera work and is the common standard for Fort Lauderdale homes due to salt-wind exposure, runs $325 to $425. A Level 3 inspection, which involves accessing hidden zones and is required when structural damage is suspected, typically starts at $500 and goes from there based on access complexity. What moves the price: number of flues, roof pitch and accessibility, whether scaffolding is required, and whether the Gelco components need destructive testing to assess hidden water damage. The estimate is free, written, and good for the job quoted, and it is handed to you before any work starts. Call (754) 354-1430 and we will give you the exact number for your house.

Why Fort Lauderdale Homeowners Call Flint Chimney Co Fort Lauderdale for Gelco Work

Hank Delano grew up in Los Angeles and learned the trade at Los Angeles Trade-Technical College before spending the better part of two decades cleaning and inspecting chimneys across South Florida, and Fort Lauderdale has been the main territory for years. Our technicians are background-checked, uniformed, and trained on Gelco products specifically, because a cap is not a cap and a chase cover is not a chase cover. When a Gelco part is not the right long-term solution for a Fort Lauderdale roof, we say so and specify a DuraFlex or HeatShield product that does the job better. Every repair carries our written 365-Day Done Right Promise, including the free return visit if a covered repair fails within that year. Tell them what you found, tell them what it costs, then do the work clean. That is how the whole crew at Flint Chimney Co Fort Lauderdale operates. Call (754) 354-1430 and we will show you what that looks like on your roof.

FAQs